Shabby Chic Gift Box

I love making this gift box.  It's so easy, and fun to decorate.  It will hold 4 or 5 lumpy, or 6 or 7 flat cards with the envelopes, and makes a great gift for those who love to send pretty cards, but don't make them, themselves.

Instructions on how to make the box here.

I used
12 x 12 card stock, Blushing Bride
4 x 5 1/2 card stock, Very Vanilla
3 3/4" x 5 1/4 Something Borrowed DSP
a little bit of Always Artichoke
Early Espresso Ink and Stampin' Sponges 
Mixed Bunch Stamp Set,
Versamark, White Embossing Powder, & heat tool,
Blossom Punch, Bird Builder Punch  
7/8" Sahara Sand Lace Trim, 
Early Espresso Scalloped Tulle Ribbon, 
Polka-Dot Embossing Folder and my Big Shot
Two buttons or brads (I recommend Antique Brads)

 The trickiest part was choosing adhesives to get the various surfaces to stick.  Here's what I used:

Layers of paper flowers to each-other:  normally, I would use snail tape or glue dots.  However, because I used split paper* to make the flower layers, I used a glue stick between the layers.  A better choice, I think, would be to use a brad, but I didn't.  Maybe next time.

Tulle to paper:  Snail tape.  Run snail onto the tulle, press one end to flower, then bunch small bits of the tulle and stick them to the flower one bit at a time.

Flower with tulle to box:  if your bottom layer of flower is smooth side down, use sticky strip for extra strength.  If the bottom is fuzzy, you won't be able to uncover the sticky strip without ripping it from the paper.  SO, here's where the brad helps.  Just add an extra scrap hidden at the bottom of the flower.  Otherwise, you'll have to use my almost fail method:  put a little Tombo (white glue) on the flower and onto the box.  Dry both with a heat tool until they are tacky.  Stick 'em together, and voila! Cement.  

Lace trim to box, Paper layers to box:  snail tape.  To get that raggedy look, don't put the snail all the way to the edge of the papers.  
Leaves to paper:  glue stick, leaving the top few leaves loose.

*Splitting your paper:  I punched out two flowers to emboss, and two to layer underneath.  I crunched up the plain ones, and when the paper began to split, peeled the layers, making four plain flowers. I used one to give the top flower a bit of loft, and three underneath the bottom flower. Using split paper gives you pretty layers without quite as much bulk. Split paper is very fuzzy on one side, so it's hard to get snail tape or glut dots to stick to it. You certainly don't have to split the layers for this project; I find it's useful when making cards to mail. 

Card Box Instructions

 

Card Box Instructions

By Gosia Hoot, Independent Stampin’ Up! demonstrator

www.gosiahoot.stampinup.net

1.     Score 12 x 12 card stock as shown.   Cut along BOLD lines.

2.     Fold along all score lines; flatten.

3.     Round corners of three top flaps. 

4.     Place two-sided tape strips along all ORANGE lines.  Do not uncover tape yet.

5.     Fold box mountain-wise along all vertical lines, so that the tape will line up.

   Uncover tape on vertical tab * only; tape to opposite side *, making box.  Tab

   should be on the inside of the box.  If your tape is on the wrong side, just fold the

   box around the other way. 

6.     Fold in two small bottom tabs (labeled “fold first,”) uncover tape strips.

   Fold in wide bottom tab labeled “fold second.”  (Do not uncover tape strip yet.)

   Press firmly to short tabs.  This is best done by using a stamp box or the side of a

   paperback book from inside the box.

7.     Place the box on the table so that the last tab (with the GREEN line) is on the table.

  Place two-sided tape along the edge of the last tab, on the side facing up (towards

  the box.) Uncover the tape on both long tabs; press last tab firmly to bottom of box.

  8.   Use a 1” circle punch to cut a semi-circle in the center of the box top the side

           without the flap.

   9.  Decorate!